kyocera ecosys fs-2000d user manual

kyocera ecosys fs-2000d user manual

Used to denote messages or names displayed on the operation panel. Used to denote operation panel keys. A high-quality printer cannot produce high-quality results when the wrong paper is used. Low-priced paper is not economical in the long run if it causes printing problems. For non standard paper, the MP tray must be used.Paper with a rough or sandy surface can cause voids in the printed output. If you are having problems with paper jams, multiple feeds, and faint printing, the paper you are using may be too thin. If you are having problems with paper jams and blurred printing the paper may be too thick. When paper passes through the fixing unit, it curls upward a little. To produce flat printouts, load the paper so that the upward pressure from the machine can correct their curling. Transparencies must be placed on the MP tray with the long edge towards the printer. When unloading transparencies (e.g., for clearing jams), hold them carefully by the edges to avoid leaving fingerprints on them. Do not remove the extra top sheet from the carrier sheet until after printing is finished. Acceptable Carrier sheet The table below lists the specifications for adhesive label paper.Refer to Paper Grain on page 1-6. This direction can easily cause wrinkles and creases when envelopes pass through the printer.Do not use paper with any kind of surface treatment, such as the type of paper commonly used for calendars. Recycled paper Select recycled paper that meets the same specifications as the white bond paper except for whiteness, refer to Paper Specifications, on page 1-. Setting the paper type for the paper source from the printer’s operation panel will cause the printer to automatically select the paper source and print in the mode best suited to that type of paper. Pull the paper cassette all the way out of the printer. Refer to Paper Size on page 2-67. Pull the release lever on the left side guide and slide to the desired paper size.

• kyocera ecosys fs-2000d manual, kyocera ecosys fs-2000d user manual, kyocera ecosys fs-2000d user manual user, kyocera ecosys fs-2000d user manual pdf, kyocera ecosys fs-2000d user manual download, kyocera ecosys fs-2000d user manual software.

Pull the release lever and slide the paper stopper to the desired paper size. When using non-standard size paper, move the paper guides and paper stopper all the way out, insert the paper, then adjust the paper guides and paper stopper to the size of the paper. Fan the paper, then tap it on a level surface to avoid media jams or skewed printing. Place the paper in the paper cassette. Ensure the side to be printed is facing down and the paper is not folded, curled, or damaged. Clip Insert the paper cassette into the slot in the printer. Push it straight in as far as it will go. Load Limit Clip. When paper is exhausted, the pointer will go down to the level of The MP tray can accommodate the various paper sizes and can hold approximately 100 sheets of paper. Adjust the position of the paper guides on the MP tray. Standard paper sizes are marked on the MP tray. For standard paper sizes, slide the paper guides to the position marked correspondingly. Align the paper with the paper guides and insert as far as it will go. Correct Incorrect Set the MP tray paper size on the printer’s operation panel. Refer to Setting MP Tray Paper Size on page 2-65. 1-20 ADVANCED OPERATION GUIDE. You can also rely on other printer utilities such as KM-NET for Clients if you need to change settings that are not available on the printer driver. It will allow remote access to printer settings. Ready PAR A4 PLAIN Menu Ready PAR A4 PLAIN. Please wait When the printer is switched on for the first time, this message will take several (Adding toner) minutes. The printer is ready to print. USB interface is in use. Serial (RS-232C) interface is in use. (option) Network interface is in use. (FS-2000D: appears only when the optional network interface card IB-30 is installed.) Network interface is in use. (option) No interface is in use. Depending on the status of lighting, each indicator has the following meaning: Indicator Flashing. Indicates an error that you can resolve.

For details, refer to the Troubleshooting section in the Operation Guide. Note that certain keys have a secondary function. NOTE: The printer has a parallel, USB, network, and an optional interface. Configuration of the printer settings affect only the interface that is currently active (shown by the INTERFACE indicator on the message display). This menu is the setting menu for administration under the Account Management System and is normally not used.Settings can be made when Ready is indicated on the printer message display. The printer prints a full list of the menu selection system — Menu Map. Note that menus shown in the list may vary depending on which optional units installed in the printer. The status page is a list of parameters and settings for most basic printer configurations. You may be required to produce a status page when requesting service to the printer. Test pattern Firmware Version This item shows the version and release date of the printer firmware. Hardware Information This item shows various printer settings for hardware-related. The PCL 6 emulation is set as default when the printer is shipped from the factory. The emulations are:. KIR Test Pattern KIR is the Kyocera’s original smoothing function. This test pattern shows the effect of the KIR (Kyocera Image Refinement) system.Since copies of the document are printed using the stored data, printing is performed faster with less computer spooling time and less network traffic. When the number of jobs reaches the limit, the oldest job will be overwritten by the new one. When the printer is turned off, all stored jobs will be deleted. You can also change the number of copies when resuming printing from the operation panel. Then, the access code must be entered on the operation panel to print a stored job. The printer prints the specified number of copies for the job. You can individually delete stored jobs by performing the following procedure. The virtual mailbox number will also appear.

The printer prints a list of jobs currently posted in the virtual mailboxes as shown in the following illustration.The value can be set between 0 and 50. This changes the Microdrive space that holds permanent code jobs. You can change the maximum space from 0 to 9999 (megabytes). The actual maximum size depends on the size of free Microdrive space. You can change the maximum space from 0 to 9999 (megabytes). The actual maximum size depends on the size of free Microdrive space.The new setting will be enabled thereafter.NOTE: This section applies to the printer having the optional serial interface board kit (IB-11) installed. You can confirm or change the serial interface parameters including baud rate, data bits, stop bits, parity, and protocol. In addition, you can install the optional network interface card in the option interface slot. NOTE: Installing the optional network interface card on the FS-2000D enables the following network settings.The IP address must be unique to the printer and should be obtained from your network administrator. The network status page shows the network addresses, and other information under various network protocols about the network interface card. The display returns to Ready. The printer prints a network status page as an example shown in the following illustration.The printer can print error descriptions when printing error occurs during KPDL emulation. The default is Off — the printer does not print KPDL errors.You can select the default font for the current interface. The default font can be one of the internal fonts or a font that is downloaded to the printer memory or stored on CompactFlash card, Microdrive or option ROM. You can change the size of the default font. If you selected a proportional font, the character size can also be changed.The printer prints out a list of fonts with a sample and font ID (number) for each of them. Sample lists of fonts are shown in the following illustration.

You can set the number of copies of each page to be printed for the current interface. KIR Mode This printer incorporates the KIR (Kyocera Image Refinement) smoothing function. KIR users the software to enhance resolution, resulting in high quality printing at resolution of 600 dpi and 300 dpi. The default is On. KIR has no effect on the printing speed. You can set the default print resolution in four ways: 300dpi, 600dpi, Fast 1200 mode and Fine 1200 mode. The CompactFlash card and Microdrive are installed into the dedicated slots of the printer. The RAM disk is an allocated part of the printer’s memory. If the Microdrive is installed in the printer, the e-MPS function will be available. For details, refer to e-MPS on page 2-19. Processing appears and the reading of data from the CompactFlash card starts. When completed, Processing disappears. You can print out the data in the CompactFlash card.This writes the file to the CompactFlash card and instructs the printer to automatically print out a CompactFlash card write information page as shown below. It is possible to use the printer to delete data from a CompactFlash card. Check that the CompactFlash card contains data.A new CompactFlash card must be formatted before it can be used in the printer. Formatting allows data to be written to the CompactFlash card. NOTE: Formatting will destroy any existing data on a storage device including a used CompactFlash card. The printer prints a list of all data names (referred to as partitions) stored in a CompactFlash card for reference. (Printing a list is also available for a font card.) The name of the written data assigned automatically by the printer. The RAM disk stores data only temporarily. When the printer is reset or turned off, the stored data will be erased. The RAM disk is allocated within the printer's memory available to users. NOTE: The file name which is displayed on the message display can be up to 16 characters.

The printer can feed paper from any paper source you command on the printer driver. The cassette mode provides a faster printing speed than the first mode. If the sizes do not match, printing will not be performed on the correct size paper. The default setting is plain paper. For more information about paper types that can be fed from the MP tray, refer to Paper Availability on page 1-2. To set the standard sizes A6 (excl. FS-2000D), A5, B5, A4, Letter, and Legal size for the paper cassette, load the paper and turn the paper size dial so that the size of the paper you are going to use appears in the paper size window (refer to Loading Paper on page 1-13). The paper size is set for the paper cassette. If you selected Custom in step 6, be sure to set the unit of measurement and the dimensions of the paper as described in the following sections. The default setting is plain paper for all paper cassettes. You can select the paper source, from which the printer feeds paper as the default. If an optional paper feeder(s) is installed, it is also available for the default paper source. Printing is performed without an error message even if the actual paper size in the current cassette differs from the paper size formatting the job. The following describes the procedure used to set a user-defined paper type for the printer. Eight custom user settings may be registered. After having been set, any of these may be called up when setting the paper type for a paper source. Press B and proceed to Setting the Paper Weight. You can set the paper thickness for your custom paper type to be customized. The total number of printed pages can also be checked on the status page. Refer to Printing a Status Page on page 2-15. It prints whatever data it has in its buffer and feeds out the page. The default form feed timeout time is 30 seconds. You can adjust the length of time the printer waits before entering Auto Sleep in the absence of data. The default time is 15 minutes.

You can print data received by the printer as hexadecimal code for debugging programs and files.The total size of the printer memory recommended for using the resource protection option is affected by several factors. Refer to Expansion Memory Modules on page 3-3. This setting is useful, for example, when the printer is located some distance from the user. The audio alarm is set to On when leaving the factory. If the alarm is set to Off, it will not sound. You can use B and A to move the cursor right and left. If the error detection setting for duplex printing has been turned On, and you attempt to print onto a paper size and paper type that cannot be used for duplex printing, the Duplex disabled Press GO error message will be displayed and printing will stop. However, there is a great deal of information on the service status page that may be useful to you. Some options are explained in the following sections.The maximum memory size is 640MB (FS-2000D, FS-3900DN: 576MB). NOTE: The expansion memory should only be installed by your service technician. Push out the clamps on both ends of the memory socket. Clamp Remove the memory module from its package. Aligning the cutouts of the memory module with the matching keys of the socket, carefully plug the memory module into the memory socket until it clicks in place. Ease the memory module out of the socket to remove. To verify that the memory module is working properly, test it by printing a status page (refer to Printing a Status Page on page 2-15). Close the option interface slot cover. Up to three paper feeders can be attached to the bottom of the printer.Holds more envelopes at a time than the MP tray. This envelope feeder can be attached to the front of the printer after the MP tray has been removed. See your dealer for purchasing information of this optional device that are. It also lists pin assignments, signal functions, timings, connector specifications, and voltage levels.

These eight signals form one byte of data sent from host computer to printer. Reception Transmission. When this signal is high, the printer is busy. When it is low, the printer is able to receive more data. This signal goes high when the printer runs out of paper. USB (Universal Serial Bus) interface specifications and interface signals are as follows. Complies with the Hi-Speed USB. Printer: B-type receptacle (female) with upstream port Cable: B-type plug (male) Use a shielded cable that complies with USB 2.0 (Hi-Speed USB) and not. The table below shows the pins and corresponding input and output signals of the RS-232C interface connector. The parameters of the RS-232C protocol are stored in the battery- powered memory of the printer.The following table summarizes the error status corresponding to different D0 values. Timing of XON transfer to host while Ready or Waiting XON sent every 3-5. Plug the end (printer side) of the RS-232C cable into the printer’s serial interface connector and screw it on securely. Plug the other end of the cable into the computer’s serial interface connector. Double click on Communications Port. The Communications Port Properties dialog is displayed for the selected COM port. Double click on Communications Port. The Communications Port Properties dialog is displayed for the selected COM port. Click on the Port Settings tab and set the port properties. At this time, the printer waits for the next data without making a page break. Form feed timeout is a function to wait only a preset amount of time before it executes an automatic page break. This tray is used instead of the cassette when printing on envelopes, postcards, transparency sheets, and labels. Check with your local solid waste officials for details in your area for proper disposal.Service personnel are advised to read this booklet carefully to familiarize themselves with the warnings and precautions described here before engaging in maintenance activities.

These symbols are described below: DANGER: High risk of serious bodily injury or death may result from insufficient attention to or incorrect compliance with warning messages using this symbol. Avoid multiple connections to one outlet: they may cause fire or electric shock.Semiconductor laser and electrophotography Printing speeds.USB memory slot Paper stopper 12. USB interface connector Top tray 13. Network indicators Operation panel 14. Network interface connector Paper cassette 15. Fuser unit MP tray paper feed unit 11.Fuser unit Toner container 11. Attaching the label. Installing the toner container and waste toner box. Adding paper to the cassette. Installing the cassette lid. Connecting the printer cables. Connecting the power cord and toner installing. Printing a status page for test. Installation guide etc. Outer case 11. Plastic bag Bottom pad L 12. Toner container Bottom pad R 13. Power cord Machine cover 14. Waste toner box Top pad L 15. Ready PAR A4 PLAIN Language label sheet Figure 1-2-3 1-2-4. Protective seal (orange colored) REMOVE THIS TAG BEFORE ADDING TONER Figure 1-2-5. Bottom plate Paper cassette Figure 1-2-8 3. Turn the paper size dial so that the size of Paper size dial the paper you are going to use appears in the paper size window. Side guide Release lever Side guide Figure 1-2-10 5. Pull the release lever and slide the paper Paper stopper stopper to the desired paper size. When using non-standard size paper, move the paper guides and paper stopper all the way out, insert the paper, then adjust the. Cassette lid Cassette lid Figure 1-2-12 1-2-9. Right side cover 3. Remove the screw and open the inner cover. Inner cover Screw Figure 1-2-15 4. Connector Clamp Network interface card Connector Figure 1-2-21 7. Install the network interface card to the option interface slot. 8. Inner cover 11. Close and secure the inner cover by one screw. 12. Close the right side cover. Connector Relay cable connector Figure 1-2-23 1-2-17.

Status Page Purpose To acquire the current printing environmental parameters and cumulative information.Item Remembers 1 to 8 of The total page count at Code of maintenance replac- NOTE: occurrence of replacement.The cleaning blade in the drum unit scrapes toner off the drum surface to clean it. Purpose To clean the drum surface when image failure occurs due to the drum. To remove paper misfed in the printer, pull out the paper cassette, pull out the rear unit, remove the devel- oper unit or open the duplex cover. When a problem is detected, the printer stops printing and display an error message on the operation panel. An error message consists of a message prompting a contact to service personnel, total print count, and a four-digit error code indicating the type of the error. USA model) only top position sensor. Optional bulk paper feeder’s tray top Defective harness Reinsert the connector. Also check for conti- DMOTRDYN signal does not go low between drum nuity within the connector harness. If none, within 2 s after DMOTONN signal goes motor and engine remedy or replace the harness. Replace developer unit. If a developer unit which is known to work normally is available for check, replace the current developer unit in the printer with the normal one. Use care not to drop foreign objects into the drum. Defective drum unit's ground. The contact (spring) in the drum unit and its counter part, the drum grounding terminal in the printer, must be in a good contact. (See page P.1-4-9, refer to figure 1-4-5) Defective drum unit. The print density may be set too high. Try adjusting the print density. For details refer to the printer's operation guide. Defective drum surface potential. If a drum unit which is known to work normally is available for check, replace the current drum unit in the printer with the nor- mal one. Defective connection Check the connection of connectors between drum PWB (YC1) between drum PWB (YC1) and connect-L PWB (YC3). Replace the power cord.

No primary paper feed.Check if the pickup roller, paper feed roller Check visually and replace any deformed and MP tray feed roller are deformed. When handling PWBs, do not touch connectors with bare hands or damage the PWB. Do not touch any PWB containing ICs with bare hands or any object prone to static charge. Top cover 3. Remove the one connector and then remove the top cover. Screw Screw Connector Figure 1-5-1 1-5-2. Registration upper roller Figure 1-5-7 4. Remove the registration upper roller from the bush. Bush Bush 8. Check or replace the registration upper and lower roller and refit all the removed parts. Registration lower roller Bush. MP tray Figure 1-5-10 3. Pull the MP tray paper feed roller holder. 4. Developer unit MP tray Figure 1-5-12. Fuser upper housing Screw Figure 1-5-19 3. Remove the screw form the fuser heater lamp. Seat the fuser heater lamp aligning its watt- Terminal age mark and welding mark faced with the correct direction and side. Latch Latch 3. Unlatch the six latches and then remove the Latch cord cover. Check or replace the fuser thermistor M and S, thermal cutout and refit all the removed parts. Cord plate Terminal Thermal. Engine PWB assembly 19. Remove the left wire guide. 20. Remove the three screws and then remove the engine PWB assembly. 21. Remove the two connectors (B) from the engine PWB. Screw Screw Connector (A) Connector (A) Connector (A) Screw (A) 25. Connector Figure 1-5-36 9. Remove the five screws and then remove the main PWB from the controller box. 10. Screw Grounding Screw terminal Screw Grounding terminal Screw Screw Screw Grounding Screw terminal Screw Figure 1-5-39 6. Remove the AC inlet. PWB connector 7. Remove the one connector. 8. Remove the PWB connector between con- nect-L PWB and then remove the power source unit. Right fan motor Clamp 2. Remove the developer unit (See page P.1-5- Hook 3. Remove the top cover (See page P.1-5-2). Connectors 4. Screw Screw 4.

Remove the four screws and then remove Screw the laser scanner unit. Downloading can be made either by directly sending the new firmware from PC via the parallel interface or using a memory card that contains the new firmware. Firmware file name example Software ID Compression. Note that you can’t download both the system and engine firmware at a time. 1. Turn printer and PC power off. 2. Note that you can download both the system and engine firmware at a time. 1. Turn printer power off. 2. Memory card Memory card slot Figure 1-6-7 13. Turn printer power on. Power switch: On 14. When message display (1) is displayed to Message display detect firmware in the memory card. Note that you can’t download both the system and engine firmware at a time. 1. Turn printer power off. 2. Feeding is performed by the rotation of the MP tray feed roller from the MP tray. Function of the MP tray friction pad prevents papers from multiple feeding. Figure 2-1-3 MP tray paper feed section MP tray paper feed roller Bottom plate. The drum unit is removable with the main charger unit.The laser beam is dis- persed as the polygon motor revolves to reflect the laser beam over the drum. Various lenses and mirror are housed in the laser scanner unit, adjust the diameter of the laser beam, and focalize it at the drum surface. The developer unit consists of the develop- ing roller where a magnetic brush is formed, the doctor blade and the agitator A and B that agitate the toner. Also, the toner sensor checks whether or not toner remains in the developer unit. The transfer roller is negatively biased so that the positively charged toner is attracted onto the paper while it is pinched by the drum and the transfer roller. The cleaning blade is constantly pressed against the drum and scrapes the residual toner off to the cleaning roller.

The heat roller is heated by the fuser heater lamp installed inside, and the toner is fused by heat and pressure and fixed onto the paper because the press roller is pressed by the fuser press spring. Operation panel PWB.Indicates the LCD message display and LED indicators. Controls key inputs. Signal Voltage Description YC101 LIVE 120 V AC AC power input Connected 220 - 240 V AC to the AC N.C. Not used inlet NEUTRAL 120 V AC AC power input 220 - 240 V AC YC102 COMMON1. Using the online preview, you can quickly view the contents and go to the page where you will find the solution to your problem with Kyocera FS-2000D. To start viewing the user manual Kyocera FS-2000D on full screen, use the button Fullscreen. However, if you do not want to take up too much of your disk space, you can always download it in the future from ManualsBase. The option to print the manual has also been provided, and you can use it by clicking the link above - Print the manual. You do not have to print the entire manual Kyocera FS-2000D but the selected pages only. paper. If you want to quickly view the content of pages found on the following pages of the manual, you can use them. The combination of optimised workplace efficiency, minimised environmental impact and effortless system integration truly sets Kyocera devices apart. ECONOMY: Total Cost of Ownership (TCO) is the true lifetime cost of a device as operating expenses can significantly exceed the original purchase price. ECOSYS devices are designed to miniWith this in mind, the new generation of Kyocera No one wants a printer to be the centre of attention. With this in mind, the new generation of Kyocera printers have been consciously designed to stay out of your way in any workgroup setting. They feature printers has been consciously designed to stay out of your way in any workgroup setting.

These printers ha the smallest f ve a remark ootprint in t ably small f heir class and are t ootprint FS-3900DN NETWORK-READY A4 WORKGROUP PRINTER Ready to go in any demanding environment, this A4 workgroup printer provides increased speed and paper capacitENVIRONMENTALLY FRIENDLY As part of Kyocera’s commitment to the environment, this new generation of printers employs ozone-free technology. Generally, printeThe standard input configuration provides a solid base that is well-suited for small workgroups. All standard paper cassettes can handle a wide range of paper stock. Additionally, all models feature space-saving internal duplex units as standard, delivering double-sided printing and reducing paper consumption. On the output. Discover everything Scribd has to offer, including books and audiobooks from major publishers. Start Free Trial Cancel anytime. Report this Document Download now Save Save Kyocera Fs-2000d, Fs-3900dn, Fs-4000dn Service Man. For Later 0 ratings 0% found this document useful (0 votes) 3K views 144 pages Kyocera Fs-2000d, Fs-3900dn, Fs-4000dn Service Manual Uploaded by supervisor3525 Description: Full description Save Save Kyocera Fs-2000d, Fs-3900dn, Fs-4000dn Service Man. For Later 0% 0% found this document useful, Mark this document as useful 0% 0% found this document not useful, Mark this document as not useful Embed Share Print Download now Jump to Page You are on page 1 of 144 Search inside document Browse Books Site Directory Site Language: English Change Language English Change Language Quick navigation Home Books Audiobooks Documents, active. And by having access to our ebooks online or by storing it on your computer, you have convenient answers with Kyocera Fs2000d User Guide. To get started finding Kyocera Fs2000d User Guide, you are right to find our website which has a comprehensive collection of manuals listed. Our library is the biggest of these that have literally hundreds of thousands of different products represented.

I get my most wanted eBook Many thanks If there is a survey it only takes 5 minutes, try any survey which works for you. To avoid print quality problems, the interior of the printer must be cleaned with every toner container replacement. Cleaning should be. The Kyocera Mita FS-1920 is ideal for business looking for speed and flexible paper handling options, in a small footprint. This desktop laser printer produces. Kyocera FS-1920, FS-3820, FS-3830 (Service manual, parts list, service bulletins, firmware), Download. Kyocera FS-2000D, FS-3900D, FS-4000D (Service. Dokumentacja, sterowniki, narzedzia, podreczniki i instrukcje obslugi produktow, zdjecia produktow KYOCERA. In the Download Centre you can download drivers, documentations and utilities for KYOCERA Document Solutions products. Additionally installation manuals. We have the following Kyocera FS 1920 manuals available for free PDF download. You may find documents other than just manuals as we also make available. Replenishing Toner. 1 Open the printer top cover all the way. Top Cover. 2 Pull the lock lever. Find device drivers, manuals, specifications and product brochures for your KYOCERA multifunctional printers and digital imaging devices. KYOCERA Document Solutions Europe. KYOCERA Advanced Search. Search. User Manual. Description, File Size, File Name. This user guide applies to the following Kyocera Wireless Corp. Download drivers, documentation and software for all your Kyocera products from a single place - welcome to the Download Centre. Reload to refresh your session. Reload to refresh your session. Be sure to check that it is the user manual to exactly the device that you are looking for. In our database Kyocera FS 2000D it belongs to the category Printer. A user manualKyocera FS 2000D is taken from the manufacturer, a Kyocera company - it is an official document, so if you have any doubts as to its contents, please contact the manufacturer of the device Kyocera FS 2000D directly.